Gallery Wall Layout: How to Plan a Photography Gallery Wall

Gallery Wall Layout: How to Plan a Photography Gallery Wall Before You Hang It

A gallery wall is far easier to plan on paper than on the wall. Before you put in a single nail, settle four things: the outer shape of the group, the largest print, the gap between the frames and the line that holds the prints together. Most people skip this part of how to make a gallery wall, and that is why most crooked gallery walls look crooked.

This guide follows one real example from start to finish. The example is a black and white gallery wall of four photographs above a 96 inch sofa, and the exact sizes and measurements are given for each print. The same steps can be used for a gallery wall in a hallway or above a bed.

Start With the Outer Shape

When you step back, the group should read as one simple shape, and most of the time that shape is a rectangle. Measure the wall and the furniture under it first. Then mark the outer edges of the gallery wall with painter's tape, so you can check the size of the group from across the room. Above a sofa that is 96 to 108 inches long, an outline about 72 inches wide stays within the two thirds to three quarters range that our sizing guide recommends.

The height of the outline will depend on the largest print, which is chosen in the next step. Above furniture, the bottom edge of the group should be 6 to 8 inches above the back of the sofa, and this rule comes before the usual center height. On an open wall, the center of the whole group goes at the same height as a single print, and our guide to choosing the right size and hanging height explains how that is measured.

Pick the Anchor Print First

Give your gallery wall one print that is clearly larger than the rest. Five or six prints of a similar size tend to look like a grid that was never lined up properly. In our example the anchor is Winter Valley, Ran Milo's black and white photograph of Yosemite Valley after a snowfall, ordered at 32x24 inches.

The frames on our paper prints add 0.7 inch on each side of the print. A 32x24 print framed without a mat therefore measures 33.4 by 25.4 inches on the wall. Use the framed size, not the print size, for every measurement in your layout. If you add a mat, the framed size stays the same and the visible part of the photograph gets smaller. We cover that in our guide to framed, matted and print only options.

You do not have to put the anchor print in the middle of the group. You can place it to one side and arrange the smaller prints around it, and that often looks more relaxed than a perfectly symmetrical layout.

Choose the Line That Holds the Group Together

A gallery wall will look organized when the eye can find at least one straight line that runs through the whole group. This line can be set up in three ways.

With a shared center line, every print is centered on the same horizontal line, so the tops and bottoms of the frames step up and down while the middles stay level. This is the most forgiving layout when the prints are of different heights.

The second is a shared top or bottom edge. You line up all of the frames along the top, or all of them along the bottom. It works best when the prints are close in height, and a shared bottom edge is how prints sit on a picture ledge.

With an outer rectangle, the prints are arranged inside the taped outline so that the outer edges of the group form a clean rectangle, while the spacing inside the group can be less regular. This layout is usually called a salon wall, and it needs the most planning of the three.

For a first gallery wall the shared center line is the easiest option, and it is the option that is used in the example in this guide.

Set One Gap and Keep It

The same gap should be used between every pair of neighboring frames in the group. For framed prints in the sizes used here, a gap of 2 inches is a good starting point. A gap of 3 inches can also work on a large wall. If the gaps are much wider than 3 inches, the prints will stop reading as one piece and will start to look like separate pictures.

The gap has more effect on the result than the exact sizes of the prints. Two frames that differ in height by an inch will still look fine if the spacing between them is the same as the spacing everywhere else in the group. Uneven spacing will be noticeable even when the frames are a perfect match.

The Example Layout, Measured

Our example layout is four prints above a 96 inch sofa. All four are black and white, all four are framed in black without a mat, and all four are centered on the same horizontal line.

Winter Valley hangs in the middle of the group. To the left of Winter Valley is Antelope Canyon B&W, a vertical photograph by Ran Milo of the curved sandstone walls inside the canyon, ordered at 18x24 inches. The framed canyon print measures 19.4 by 25.4 inches, which is exactly the same height as the anchor print, so the top and bottom edges of these two frames will also line up.

To the right of the anchor print there are two horizontal prints, one hung above the other. The upper print is Grandfather Tree, a lone weathered pine on a rocky hilltop in Yosemite, and the lower print is Solo Surfer, a lone surfer at the edge of the water. Both photographs are by Yiftah Shahar and both are ordered at 14x11 inches, which becomes 15.4 by 12.4 inches when the prints are framed. With a 2 inch gap between the two prints the column is 26.8 inches tall, so a column centered on the same line as the anchor print will extend 0.7 inch past the anchor print at the top and at the bottom. On this side of the group, the shared center line and not the edges of the frames holds the layout together.

Now add up the width. You have 19.4 inches for the canyon print, 2 inches of gap, 33.4 inches for the anchor, another 2 inches of gap and 15.4 inches for the column on the right, which comes to 72.2 inches. Above a 96 inch sofa that leaves about 12 inches of open wall on each side of the group, and it matches the outline you taped to the wall at the start.

The tall canyon print on the left is balanced on the right by two smaller prints. Grandfather Tree and Solo Surfer were chosen for that column because each of them has a single subject alone in the frame, a tree and a surfer, so the two of them stay quiet next to the larger anchor print.

Keep the Prints Related

A gallery wall can include different subjects, but the prints will need at least one thing in common to tie the group together. Color and frame are the easiest things to keep the same, and a black and white gallery wall with matching black frames will hold together even when the subjects range from a canyon to a beach. One Inframe customer, Kim, ordered a print with a black wood frame for a wall full of black and white photos and wrote that "it fit in perfectly." Black and white prints can be mixed with color photographs, but the mix usually works only when the color prints are muted.

Prints chosen from one or two photographers will also help, because the same photographer will usually work with similar light and similar contrast across many images. In the example in this guide all four prints are by Ran Milo or Yiftah Shahar, and all four prints can be found in our black and white collection, which is also a good place to put together a gallery wall art set.

The frames should also be the same color across the whole wall. Mixed black, white and natural frames usually look unplanned unless the wall is meant to look like a collection that was built up over years.

How to Hang a Gallery Wall From the Plan

Our sizing guide describes the paper template method, and a few details make the method work better for a gallery wall. When the frames arrive, measure the distance from the top of each frame to its hanging hardware and mark that point on the template for the frame, because the hardware is rarely in the same place on frames of different sizes. The templates should stay up for a day or two before the layout is final, since this is the last stage when prints can be moved without extra holes in the wall.

The anchor print should be hung first, and the work should then proceed outward from the anchor print. Every gap should be checked with a 2 inch spacer, such as a scrap of wood cut to that width, while the work is done.

A long level or a laser level will make it much easier to keep the shared center line straight across 6 feet of wall.

Frequently Asked Questions

How far apart should frames be on a gallery wall?

A gap of about 2 inches between frames will work for most framed photography prints, and the same gap should be used everywhere in the group. On a very large wall the gap can be increased to 3 inches. Uneven gaps are more noticeable than small differences in the size of the frames.

How do I adjust this layout for a different sofa?

The 2 inch gaps and the shared center line should be kept and every print should be ordered one step smaller. With Winter Valley at 24x18, Antelope Canyon B&W at 12x18 and the two horizontal prints at 10x8, the group is 54.2 inches wide, and this width suits a sofa of 72 to 84 inches. The canyon print and the anchor print will still share the same framed height, which is 19.4 inches.

Should all frames on a gallery wall match?

For a photography gallery wall, matching frames are the safer choice. A black and white gallery wall in all black frames will read as one piece. Frames in mixed colors can work on a wall that is built up over a long time, but the frames will need a strong common subject or palette to hold the group together.

Can I mix vertical and horizontal prints on a gallery wall?

Vertical and horizontal prints can be mixed on a gallery wall, and most gallery walls do mix them. All of the prints should be centered on one shared line, and sizes that have the same framed height should be chosen where possible. In the example in this guide, an 18x24 vertical print and a 32x24 horizontal print are both 25.4 inches tall when framed, so the top and bottom edges of the two prints line up exactly.